How do I set the time on my Balboa hot tub?

High Range can be set between 26.5°C to 40°C. Low Range can be set between 10°C to 36°C. To change the range press the temp/warm button followed by the light button, then press temp/warm button again. To exit, press the light button or wait for 10 seconds to go back to the Main Screen.

High Range can be set between 26.5°C to 40°C. Low Range can be set between 10°C to 36°C. To change the range press the temp/warm button followed by the light button, then press temp/warm button again. To exit, press the light button or wait for 10 seconds to go back to the Main Screen.

One may also ask, how do I reset my hot tub control panel? How to Reset a Spa Heater

  1. Locate the spa’s high-limit reset. This is a red button found on many spa packs.
  2. Press the high-limit reset button.
  3. Turn on your spa and observe its operation.
  4. Flip the breaker panel switch on or press the reset button on the GFCI outlet to restore power.

In this manner, how do you set a hot tub timer?

Instructions: how to set the pump time for your pool and hot tub

  1. Locate and open the panel with your pool or hot tub pump timer. This should be located close to the pool pump itself and the hot tub.
  2. Set the on and off switches to the desired times.
  3. Disengage the time dial and set it to the current time.

How long should filter cycle run on hot tub?

Typical filtration cycles are four hours, twice per day (for hot tubs operating a single or two speed pump). Reducing the cycles to 3 hours twice per day will save water pumping energy. These circulation times should be set for off-peak hours.

What does sn mean on a hot tub?

SN usually means the sensors are out of sync – they are giving different temperature readings to the circuit board. Balboa allows up to a 2 degree variance in temperature between the sensors, than assumes the tub is heating unevenly and shuts down the tub to prevent damaging it.

How much is a circuit board for a hot tub?

Hot Tub and Spa Circuit Board Replacement Parts Brand Price Balboa Water Group $259.95

What does code SL mean on hot tub?

If the SLP or SL Message is ON Solid (Not Flashing) on the Display, the Spa is Operating in the Sleep Heating Mode, but there is No current water temperature because the Spa is between Filter Cycles. Other Heating Modes are Standard, Standard in Economy, and Sleep Modes. Ecn or Ec is ON Solid (Not Flashing):

What is SL mode on hot tub?

While your hot tub is in sleep mode (or ‘SL’ & SLP mode on some models), the jets will operate occasionally to filter the water. In sleep mode, your hot tub’s heater will usually only kick on once the temperature dips below 20 degrees of the set temperature.

What does PR mean on Balboa hot tub?

dr = Inadequate water detected in heater. dry = Inadequate water detected in heater. (Displays on third occurrence of “dr” message). Spa is shut down. Pr = When spa is first actuated, it will go into Priming Mode.

What mode should my hot tub be in?

Note: Economy mode should only be used if you are not planning on using the hot tub for two or more days, any less than that and it is more efficient to keep it at a set temperature. You can instead lower the set temperature by 2 degrees.

Should I leave my hot tub on all the time?

Yes, you should leave your hot tub on all of the time. Hot tubs are designed to always be switched on and it’s more economical to keep the water hot than it is to heat it up from cold each time you want to use it.

Should I leave my Lay Z Spa on all the time?

Leave Your Lay-Z-Spa Heater Activated Between Uses Depending on the amount of use your spa gets, in our experience it is better to leave the heater activated all of the time, if used regularly – say 3 or more times per week.

How do you set a timer?

Steps Find the outlet closest to your device. Flip the manual switch button to “Timer On” and insert the timer into the outlet. Turn the dial clockwise to the current time. Pull or push the timer pins up or down around the dial to set the device time. Connect your electrical device to your plug timer.

Is Lazy spa pump waterproof?

Is the pump waterproof & can the pump be left out all year round? Yes a Lay-Z-Spa pump is water proof, however if you are expecting a very large amount of rain or bad weather it is recommended that you bring the spa and pump indoors.

How do you set a Grasslin digital timer?

How to Set a Grasslin Timer Press the “Plus” or “Minus” button on the timer’s control panel to switch between 24-hour or a.m./p.m. time format. Press the “Plus” or “Minus” button to advance the hour to the correct time, then press the “OK” button.