How much does it cost to pave a parking lot per square foot?

How Much Does Commercial Parking Lot Paving Cost? On average, it costs between $1.49 and $1.69 per square foot to re-pave an asphalt parking lot. Striping, marking, and curbing will come at an additional cost. Based on this estimated rate, it would cost about $16,000 to re-pave a 10,000 square foot parking lot.

Paving an asphalt driveway costs $4,559 on average, with a typical range between $2,856 and $6,314. This project runs $7 to $13 per square foot, including $2 to $6 per square foot for materials and $5 to $7 per square foot for labor. If you need replacement, you’ll pay $8 to $15 per square foot.

Subsequently, question is, how much does it cost to pave a 200 foot driveway? The average cost of a concrete driveway, by comparison, is almost $7,400. Other sources estimate the cost to install an asphalt driveway to be between $2,300 and $10,300. Homeowners typically pay per square foot. Reibling adds the average cost per square foot is between $3.50 and $4.50.

Also know, how much does it cost to pave 1 acre?

The PAVE-A-LOT works just as well as the expensive units but sells for a fraction of the cost. Every aspect of the PAVE-A-LOT is easy to learn and the paving can be done at your convenience. This method of paving will save you at least half the cost, which is about $10,000.00 to $12,000.00 per acre.

How much does a parking garage cost per square foot?

The above figures place this construction at a $59 per square foot cost, though a national average of stands between $50 to $70 for most projects.

What is the cheapest way to pave a driveway?

Cheap Ways to Pave a Driveway Rustic Gravel. Gravel is one of the most inexpensive paving options for a driveway. Durable Apshalt. Asphalt is usually quite affordable. Elegant Tar and Chip. A tar and chip driveway is an affordable driveway paving option that often has a more decorative appearance than plain asphalt. Low-Maintenance Concrete.

What type of driveway is cheapest?

Pound for pound, aggregate is the cheapest of these four common driveway materials. A basic gravel driveway can cost as little as $0.50 per square foot – an order of magnitude less than a professionally installed asphalt, stone, or concrete driveway. Durability. Aggregate is extremely durable.

How much does it cost to pave a 2 lane road?

Nonetheless, here are the daunting numbers: constructing a two-lane, undivided road in a rural locale will set you back somewhere between $2 and $3 million per mile — in urban areas, that number jumps to between $3 and $5 million.

Is a brick driveway cheaper than concrete?

In the long run, brick paver driveways can prove to be less of a hassle, and more cost-effective, than concrete driveways are. These alternative driveway surfaces are easier to maintain, are safer in wet conditions, and they are much simpler, and cheaper to repair.

Which is cheaper concrete or asphalt driveway?

The cost of an asphalt driveway is typically cheaper than concrete, costing $2.00 – $4.00 per square foot. Asphalt prices tend to fluctuate with fluctuations in crude oil prices. In contrast, a concrete driveway costs between $4.00 – $6.00 per square foot for a standard installation.

Is 2 inches of asphalt enough for a driveway?

The granular base aggregate used for a residential driveway is typically 6 to 8 inches. On top of this layer, residential driveways typically use 2 to 3 inches of asphalt, whereas commercial driveways use about 3 inches.

How much is a ton of blacktop?

In terms of bulk price, asphalt is priced by the ton. One ton of asphalt covers about 80 square feet with 2 inches of material or 160 square feet with 1 inch of material. Current wholesale pricing of bulk base-grade asphalt is $70-$80 per ton; top-layer grade is $75-$85 per ton.

Can you pave over existing asphalt driveway?

Asphalt Resurface (over Asphalt): A #404 surface course of asphalt can be installed on top of existing asphalt. Since the product used for both layers is the same, the layers should heave together in the winter. The time to correct them is before you install the new asphalt.

How thick should an asphalt driveway be?

In many cases a 4-inch thickness may be adequate, but 5 or even 6 inches of full-depth asphalt will assure you of a stronger, stable driveway under a wider range of climate and loads. As an option, some contractors use 6 to 8 inches of compacted aggregate, or gravel, as a base for 3 inches of asphalt pavement.

How much does a ton of asphalt cover?

The area that 1 ton of asphalt covers depends on the thickness of the asphalt to be used; for a half-inch thick section of asphalt, 1 ton will cover approximately 316 square feet, while 1 ton of asphalt will cover 79 square feet when laid several inches thick.

How long should an asphalt driveway last?

12 to 20 years

How much does it cost to pave a lot?

How Much Does Commercial Parking Lot Paving Cost? On average, it costs between $1.49 and $1.69 per square foot to re-pave an asphalt parking lot. Striping, marking, and curbing will come at an additional cost. Based on this estimated rate, it would cost about $16,000 to re-pave a 10,000 square foot parking lot.

How much should a driveway cost?

The national average cost to install a concrete driveway is about $6 a square foot. According to Joe Pilson, owner of Complete Concrete in Denver, Colorado, a typical driveway big enough for one car and room to turn around is about 500 square feet, with an average total project cost of $3000.