What does it mean when my washer says UB?

The Ub error code on the LG washing machine display is an indication of a TUB IMBALANCE or ITEMS NOT DISTRIBUTED PROPERLY issue.

Samsung washer error code U6. When the Samsung washing machine displays a U6 error, it means the drum is out of balance during a cycle. This is a common Ub error code.

Also, what is PE error in washing machine? The PE error code indicates that the water level sensor is malfunctional. To fix this: Unplug the washer for 10 seconds. Plug the washer back in, and restart the cycle again.

Additionally, how do you fix an unbalanced washing machine?

How to Repair a Washing Machine that Is Unbalanced

  1. Step 1 – Check Level. Place a straight level on top of the washer to see how much off balance the washing machine is.
  2. Step 2 – Level with Legs. Most washing machines come with adjustable legs in the front and the back.
  3. Step 3 – Tighten Drum.
  4. Step 4 – Keep Large Items Out.

What does AE mean on washing machine?

flood protection device

Why is my Samsung washer not spinning?

To determine if the drive motor is defective, first ensure that the motor is getting power. If the drive motor hums but doesn’t run, is noisy, or does not turn freely, replace it. The washer transmission might be worn out or defective. Transmissions have gears in them that can fail causing the washer to not spin.

How do I troubleshoot my Samsung washer?

SAMSUNG WASHER FIX/SOLUTION: Check the fuse or reset the circuit breaker. Straighten the drain hoses. Eliminate kinked hoses. If there is a drain restriction, troubleshoot it. Close the door and press the Start/Pause button. For your safety, your washer will not tumble or spin unless the door is closed.

What is OC in washing machine?

Samsung Washing Machine Error Codes OE, 0E, OC, 0C, 1 OC, 1 0C – Water overflow issue. Two common reasons are faulty water inlet valve or defective water level sensor. If water filling up by a little even with the machine being OFF, thats mean inlet valve not keeping water pressure and not fully closed.

Where is the drain filter on a Samsung washing machine?

Clogged drain filter Place a shallow pan in front of the filter door at the bottom of the washer to collect water left in the tub. Open the drain pump filter door, pull out the drain tube and remove the drain tube plug. Pull the filter out of the pump and clear any debris from the filter and pump housing.

How do I reset my Samsung washing machine?

To reset your Samsung washing machine you need to simply disconnect the washing machine from power for 5 to 10 minutes. (Unplug the washer from the wall outlet or flip the breaker in the breaker box for the washing machine).

How do I fix my Samsung Washer error code 3e?

How To Fix 3E Samsung Washer Error Code: Unplug The Washing Machine: Unplug the washer for 2-3 minutes. Check Wire Connections On Drive Motor: One fairly common issue that causes the 3E error code is connection problems. Check Wire Connections On Control Board: Check Hall Sensor:

How do I fix the OE error on my Samsung washing machine?

OE can be triggered by a kinked drain hose or a clogged drain pump filter. Check for kinked drain hose. Check behind the washer to ensure that the drain hose is not kinked or clogged. Test the drain pump. Do you hear the humming sound? Clean drain pump filter. Run tub clean cycle. Request Repair.

Why is my washing machine shaking violently?

Possible Cause: Unbalanced Washer The spin speed of an average washing machine is between 600 – 1400RPM. If the washing machine is not balanced, it may shake violently during the spin cycle, causing water to spill on the floor. A washing machine imbalance can be caused by a unit that does not sit level to the ground.

What causes a washer to be unbalanced?

All front-load washing machines have shock absorbers that are used to dampen the tub movement in the spin cycle. When shock absorbers weaken or become damaged, unbalanced loads will cause the washer to shake or move and the machine will often make a loud banging sound during the spin cycle.

What causes bearings to go in washing machine?

Both front and top load washers use bearings that will eventually become defective with use. Over time, water seeps through the seal and rusts the bearings. Rusted bearings are the main cause of the loud noise that you hear when the washer is spinning.

Why is my washing machine making a banging noise when spinning?

The most common reason for a noisy washing machine is that you’ve overloaded the tub or that the clothes in the tub are unevenly distributed. This causes the inner tub of the washing machine to spin unevenly, often hitting against the outer tub and creating the banging noise.