What kind of antifreeze does a Jeep Liberty take?

Prestone 50/50 is a blend of concentrated antifreeze/coolant and demineralized water. Prestone 50/50 Prediluted Antifreeze/Coolant with Cor-Guard is compatible with ANY antifreeze/coolant, regardless of color, and can be used in ALL makes and models of cars and light duty trucks.

Ethylene glycol based coolant w/ HOAT. Takes 14 quarts. If you are flushing the coolant out completely you can use the green stuff, but the zerex is what is originally used.

Also Know, how much antifreeze does a Jeep Liberty hold? Fluid Capacities and Type

Capacity (Quarts) Capacity (Liters)
Engine (2.4L) 5.00 QUARTS 4.70 LITERS
Engine (2.5L Diesel) 6.90 QUARTS 6.50 LITERS
Engine (2.8L Diesel) 6.40 QUARTS 6.00 LITERS
Cooling System (3.7L) 14.00 QUARTS 13.00 LITERS

In respect to this, what kind of antifreeze does a 2008 Jeep Liberty take?

Prestone 50/50 Ready-To-Use Prediluted Extended Life AMAM Antifreeze/Coolant, 1 Gal.

How do you drain the coolant in a Jeep Liberty?

  1. Getting Started.
  2. Overview. How to determine cooling system type.
  3. Open the Hood.
  4. Find Reservoir. Locate the coolant reservoir and clean it.
  5. Drain Reservoir. Remove coolant from the reservoir.
  6. Radiator Cap. Remove the radiator cap before draining.
  7. Drain Point. Locate the drain point on the radiator.
  8. Drain Coolant.

Can you mix antifreeze?

The green and orange coolants do not mix. When mixed together they form a gel-like substance that stops coolant flow and consequently the engine overheats. There are some coolants that claim compatibility with Dexcool, but I would rather err conservatively and add what the system is supposed to take rather than gamble.

Where do you put coolant in a Jeep Grand Cherokee?

Put a bucket underneath the radiator and directly below the drain plug. On most models of the Jeep Grand Cherokee, you’ll find the plug on the bottom of the radiator on the right side.

How do you fill a Jeep Wrangler radiator?

Fill the coolant expansion tank approximately 1/3 of the way with distilled water. Leaving the radiator cap off, start the vehicle and turn the heater to the fully ‘ON’ position. While the car is idling, top off the radiator as needed before installing the cap.

What is Hoat antifreeze?

Hybrid Organic Acid Technology (HOAT) is a combination of IAT and OAT. Several manufacturers are using HOAT for their vehicles. One version is dyed orange and contains 10% recycled antifreeze. Nitrited Organic Acid Technology (NOAT) is an OAT with nitrite added.

When should antifreeze be used in the cooling system?

Here’s why: Most vehicles use long-life engine coolant (usually a 50/50 mixture of antifreeze and water) in the radiator that for several years will provide protection against boiling in hot weather and freezing in cold temperatures, with little or no maintenance.

How do you change the transmission fluid in a Jeep Liberty?

How To Change Transmission Fluid 02-07 Jeep Liberty Have a drain pan ready. Remove eleven of the fourteen 10mm bolts from the transmission pan. Leave three bolts loosened but not removed at each end of the transmission pan. Pry down the front of the transmission pan. Allow the transmission fluid to drain. Remove one of the bolts. Allow the transmission to drain further.

What kind of antifreeze does a 2007 Jeep Wrangler take?

The 2007 Jeep Wrangler recommends Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) coolant.

What kind of oil does a 2009 Jeep Liberty take?

Jeep Liberty 3.7L 2009, SAE 5W-20 Full Synthetic Motor Oil, 1 Quart by Idemitsu®.

How much antifreeze does a Jeep Wrangler hold?

Wrangler Cooling Capacity Generally, each generation of Jeep had much of the same coolant capacity. Most 4.0L engines hold about 6 quarts of 10W-30 coolant, although the 4.0L JK series requires 5W-20 coolant. For more information about your coolant capacity check out our coolant capacity chart.